The coil length of each part is 2.5 m and is equipped with its own separate cryostat.

Parameters of the superconductiong solenoid

The central part and both of the end parts consist of 257 and 278 turns of coaxial coil windings with double layers. This configuration is to compensate the field drop along the beam axis. The superconducting magnet requires a relatively thick iron yoke to ensure the 2 Tesla uniform field in the central tracking region. In order to keep the maximum field in the iron yoke below 2 Tesla, we need a total amount of 11,500 tons of iron. The overall inductance of the magnet is 5.5 H. Consequently, the total stored energy is 1.1 GJ when the magnet is operated at 20 kA to produce the 2 Tesla central field.
One of the most important issues in the design of the superconducting coil is the method of cooling. For the JLC detector magnet, a direct cooling system is applied with the flow of two-phase helium through a cooling path in the conductor. In this case, it is very important to reduce the pressure drop since the cooling path is very long. Three modules are cooled in parallel. Also, in our design, two shields cover the coil at 20 K and 80 K. The 20 K shield is essential to reduce the helium amount further by controlling the pressure drop to be less than 0.2 kg/cm2.

The cryostat is a vacuum chamber with superinsulation. Two shields at 20 K and 80 K are cooled by the helium gas flow from the refrigerator. The heat flow to each coil is 4 W/coil, resulting in 12 W in total. This corresponds to a liquid helium flow of 6 g/sec. It is expected to take a long time for initial cooldown since the path is very long. To reduce the cooldown time, we are considering extra cooling channels on the outer cylinder of the coil. The total heat load for this magnet at 4.2 K is estimated to be about 330 W. Therefore, a medium class refrigerator with a cooling power of 500 W (corresponding to electric power consumption of 500 kW) is enough to operate the magnet.

Conductor

Parameters of the superconductiong solenoid

The operation current and maximum temperature are 20 kA and 5.0 K, assuming that the helium pressure at the inlet is 0.3 kg/cm2 and the local temperature rise is 0.5 K. On the other hand, the critical current of the conductor is 40 kA at 5.0 K in a 3 Tesla field (50 kA at 4.2 K in the same field).
The coil is made of NbTi/Cu multifilamentary superconducting cables. The cable consists of 10200 filaments with 50牛 in diameter. The NbTi/Cu ratio is chosen to be 1/2 for easy mechanical handling. The cross section of the NbTi is conservatively designed so that the current density is 2500 A/mm2 at 4.2 K in 3 Tesla. The superconductor is soldered to Cu stabilizer in which the cooling path is placed. The diameter of the path is 14 mm and the length in one module is about 8 km. The overall NbTi/Cu ratio is 1/36 and the current density of this Cu part is about 25 A/mm2 when the magnet gets quenched. This current density is expected to be low enough, from a simple quench simulation, to keep the local maximum temperature rise less than 80 K, so that the magnet is safe from local mechanical stress.

Energy Extraction

The stored energy has to be safely extracted on encounter with a quench. In our magnet design, all of the three modules are connected to a single dump resistor of 0.1 W, which absorbs all of their stored energy even when only one of them gets quenched. This is to avoid unbalanced force between the coils and the iron yoke. The maximum voltage at the energy extraction is 2 kV between the current leads.

Getting Started

• "jlcsmag@jlcux1.kek.jp": JLC magnet subgroup activities and announcements

Magnet Subgroup Calendar

• June 29-July 1, 1995 3rd JLC Physics Meeting, Tokyo, Japan.
• Sep. 8-12, 1995 LCWS95, Iwate, Japan.

Library

• Reports
• List of Papers (PS/TeX)
• Minutes of JLC Magnet Subgroup Meetings

Back to JLC Home Page